APA107 RGB Pixel Digital LED Strip Lights
Technical Parameters
LED Light Source: 5050 SMD LED,
Viewing angle: 120 degrees
Working voltage: DC5V
Color: White, Warm white, Natural white, Red, Green, Blue, Yellow,
RGB
PCB Width: 8mm, 10mm, 11.5mm, 12mm, 13.5mm, 15mm, 20mm
PCB color: White
LED Quantity per meter: 30led, 60led, 72led, 144led
Waterproof rate: IP20, IP33, IP65, IP67. IP68
Waterproof method: Surface Epoxy Plated, Silicone Pipe, Full
Silicone Gel
Working temperature: -20~+60 celsius degree
Packing: 5m/roll, 1roll/bag
APA107 will be upgraded again, the PWM can be 26-28kHz, faster and
cheaper than APA102.
APA107 is a type ic for the three-color RGB Diming control strip
and string ,This ic using the CMOS process to provide three-color
RGB LED output driver to adjust the output with 256 gray scale and
32 brightness adjustment, APA107 with 2 signal output way, one is
clock ,another is data, the clock and data is synchronizated,so
that the crystal cascade piece of output movement is sychronizated.
Features:
1, Control IC included,supporting numerous color-change effects.
2, Absolutely addressable,each IC built inside RGB LED.
3, Each IC control one leds.
4, APA107 have 4 Wire input and output : Data ,Clock ,GND ,Anode,
build in ic, double signal .
5, Grey scale 256, 256(Red)*256(Green)*256(Blue) colors that APA107
LED can change to. Keep LED show smooth color effect when changing
color.
OPTICAL PARAMETERBASIC PARAMETER
LED Q’ty: 30LEDs/m, Pixels: 30/m , Gray Scale:256
Power/m: 9W, Input voltage: DC5V, Max current/LED: 60Ma, Warranty:
3years,
Illumination Angle: 120° , Working temperature: -20℃~+45℃, Working
hour: 30000h
Energy grade: A, SMD LED spacing: 33.08mm, CRI(Ra): >80Ra, PCB:
White/Black
Minim cuttable length: every LED is cuttable, PCB Width: 10mm
The upgraded type of APA102 Pixel Digital LED Strip Lights.
Applications
Indoor and outdoor decoration lightings.
Idea for in advertisement and cabaret, large scale backlight,
cabinet, furniture, landscape outlines
Edge-lighting of transparent or diffused materials, to couple light
into transparent or diffused glass
Bridge edge lighting
Window display lighting
Car and motorcycle decorative lighting
Path & Building contour decorative lighting
Emergency hallway lighting / rescue signs / advertising signs /
light boxes
Architectural decorative lighting, villa, restaurant, hotel,
meeting room, show room, shop, counter, etc
Festival lighting, General lighting, Task lighting, Household
appliances, Architectural lighting, Decorative / pathway lighting,
Street lighting
Safety Information1. The SMD light ribbon itself and all its components may not be
mechanically stressed. Assembly must not damage or destroy
conducting paths on the circuit board.
2. Installation of LED light ribbon (with power supplies) needs to
be comply with all applicable electrical and safety standards. Only
qualified personnel should be allowed to perform installations.
Correct electrical polarity needs to be observed. Wrong polarity
may destroy the ribbon.
3. Parallel connection is highly recommended as safe electrical
operation mode.
4. Serial connection is not recommended. Unbalanced voltage drop
can cause hazardous overload and damage the ribbon.
5. Please ensure that the power supply is of adequate power to
operate the total load.
6. When mounting on metallic or otherwise conductive surfaces,
there needs to be an electrical insulated points between ribbon and
the mounting surface.
7. Please pay attention to standard ESD precautions when installing
the ribbon.
Absolute Maximum Rating at TA=25°C |
Parameter | Symbol | Absolute Maximum Rating | Unit |
ATA-NF60 |
Forward Current | IF | 2000 | mA |
Forward Voltage | VF | DC 12 | V |
Electrostatic Discharge | ESD | 400 | V |
Operating Temperature | Topr | -25~+60 | °C |
StorageTemperature | Tstg | -40~+80 | °C |
User Manual:
Switch off power of the mains supply or respectively of the
connection lead before doing any works.
The complete installation must be done by an electrical expert who
is familiar with the valid directives.
Quaity Control:
Stability TEST: make sure 100% of the lamps be aging test at least
48hours
Lighting TEST: make sure 100% of the lamps be lighted before
packing
Drop TEST: make sure every single light have been well protected by
box
Contact:
Peony Jin
Mobile: 0086-180 0253 2737
Please feel free to send us your inquiry, We are at your service
any time!