Series 3-6-12 Steering Control Unit Non Load Reaction 15.2 Cu In/Rev 8-16 GPM Flow Range 3/4-16 St.Thd O-Ring Ports

Series 3-6-12 Steering Control Unit, Non-Load Reaction,15.2 cu in/rev, 8-16 GPM Flow Range, 3/4-16 St.Thd O-Ring Ports

Hanjiu hydraulic supply eaton charlynn series 3-6-12 hydraulic steering units,

used on wheel loaders, backhoe loaders, tractors, forklifts,marine machines,harvesters....

same quality, high performance

type code :BZZ1-E250BA-C

specification:

The installation and use of full hydraulic steering note

1 installation precautions:

• (1) When installation steering gear must ensure coaxiality with column, must have a gap of 1 mm in the axial direction.
• (2) The depth of screw connection to the steering column tightening steering column is ≤15mm.
• (3) After steering gear installed, must check steering wheel turns to ensure the flexibility of the return position.
• (4) Connection pipeline: P oil port connects to the oil supply pump, T oil port connects to the oil tank, and A and B oil ports respectively connect the left and right oil chambers of the steering gear.

2 oil flow rate considerations:

• (1) The oil supply circuit connected to the P oil port, the oil flow rate in the pipe is recommended to be ≤1.5m/s.
• (2) The pressure circuit of the oil cylinder connected to the A and B ports is recommended. The oil flow rate in the pipe is recommended to be ≤4~5m/s.

3 other matters needing attention:

• (1) The diameter of the steering wheel must not exceed 500mm.
• (2) A return filter with a filter accuracy of 30 μm should be installed in the return line of the steering gear. The position of tank is generally higher than installation position of steering gear, and return pipe is inserted below oil level, so oil can be filled only when the manpower is turned, and air can be prevented from entering the oil line.
• (3) The oil viscosity of steering gear is 17cst~33cst. It is recommended to use low-condensation hydraulic oil. Steering gear allows normal working oil temperature 20°C to 80°C, and the limit working oil temperature range is -30°C to 100°C. Reminder: In Caase of abnormal oil temperature, steering performance will decrease.
• (4) After steering system assembled, it shall be tested: clean oil tank before operation, inject hydraulic oil to the max oil level.Loosen cylinder nipple and allow pump to run at low speed until it is out of oil. Remove link,turn the steering wheel so that the piston reaches left or right position, and then fill the tank to specified level. Tighten all thread connections, connect the piston rod, and check if the steering system is working properly.
• (5) It must be ensured that the oil is clean to prevent the dirt to cause steering failure. Always check the condition of the filter element and the oil. If necessary, give a replacement.
• (6) If steering failure, must be carefully check the reason first. The steering wheel must not be pulled hard, and the steering gear should not be disassembled to avoid damage to parts. It is forbidden for two people to turn the steering wheel at the same time.

HANJIU brand hydraulic motors, hydraulic valves, orbitrol are affordable and have good performance.

DANFOSS OSPC

ORBITROL

STEEING UNITS

STEERING PUMP

STEERING MOTOR

SPOOL VALVE

Shijiazhuang Hanjiu Technology Co.,ltd. is a professional manufacturer of industrial hydraulic components, located in China - Hebei City. Since 1995, Hanjiu focused on the development and production of full series of hydraulic components, orbit motors, steering orbitrols, directional control valves.

Our products include: GEROLER and GEROTOR motors, hydraulic steering units, directional control valves. More than 50 series, 2000 types. Personalized products and services to provide customers with a significant advantage. Due to the high quality of our products and reliable performance, they are widely used in mobile, industrial, fluid power, dynamic, agricultural, construction, marine, automation, transport, sanitary, etc.

Hanjiu Technology brings together the world's top professional talent and technology, has a highly qualified international personnel. Set from software development to hardware design, system testing, technical services are completed by professional and technical personnel. We have R & D base in Hebei, well-known institutions of higher learning and research institutions at home and abroad, work closely with national patent applications for 63, a number of the core technological achievements and technical indicators at the international advanced level.

To ensure the quality and stability of the machine, we use the most advanced production and testing equipment to check the quality and performance of our hydraulic motors and steering units and valves in each production step to ensure our hydraulic components perfect quality and stable performance.

We provide customers with affordable, high-quality hydraulic components. In order to achieve the advantages of Asia, the full benefit in terms of quality and cost, procurement of key machine from Germany, and the production and manufacturing in China. We have the best supply chain in China and parts manufacturers, and a solid record of quality and innovation, to prove that our 20+-year performance of the hydraulic components

Quality product performance and good reputation, our products are not only successful sales in China, and have been exported to more than 120 countries and regions in the world, including: Germany, Japan, Italy, Spain, Poland, Russia, Belarus, South Korea, Turkey, Egypt, Brazil, Argentina, Chile, India, Australia, the United Arab Emirates, Saudi Arabia, USA, Mexico and other countries, the products are subject to a great welcome and praise.

Our goal is simple: to sell the best hydraulic motors, steering units, valves, components at the best prices, and provides industry-leading customer service. We personally get to know each of our customers, and we know how to discover the most valuable part of our business is Perfect Hydraulics, to help others achieve their goals.

For more detailed information on our hydraulic components, please do not hesitate to contact us! We welcome your inquiries, and look forward to working with you.