Product Details
Company Profile

684k Capacitor 0.68 UF 275VAC Non Induction Construction

Non-Induction Construction 0.68uf 684K 275VAC X2 Safety Capacitor Long Life Due To Self-Healing Effect

X2 Safety Capacitor.pdf

Characteristics of X2 Safety Capacitors

Non-inductive construction with metallized polypropylene film.
Excellent moisture resistance.
self-healing.
Excellent flame retardant properties.
Capable of withstanding overvoltage shocks.

The use of X2 safety capacitors.

Suppresses electromagnetic interference.
Jumper the lines.
It is suitable for the resistance-capacitance step-down of ammeters, LED drivers, controllers, etc. in series in the circuit.

Products Introduction

MPX are winded with metallized polypropylene film dielectric,Non-inductive construction, tinned copper wire leads,and flame retardant epoxy resin coating. They have excellent features of self-healing and good flame retardant according to UL 94-V0

Features

1 Non-induction construction

2 High moisture-resistance

3 Self-healing property

4 Flame retardant type(compliance with UL 94V-0)

5 Very small loss

Construction and main materials of products

Specifications(IEC 60384-14)

Test items	Performance requirements	Conditions of test
Capacitance	Within the tolerance specified	1KHz, 1Vrms Max. at 25℃
Dissipation Factor	0.001 (0.1%) Max.	1KHz, 1Vrms Max. at 25℃
Voltage proof	Shall be no abnormality	Between terminals 4.3UR (Vdc) Test of 60sec.
Voltage proof	Shall be no abnormality	Between terminal and enclosure UR×200％+1500Vac, 60sec.
Insulation resistance	CR ≤ 0.33μF IR ≥ 15,000MΩ CR >0.33μF IR ≥6,000s	100±15Vdc, 60sec / 25℃
Robustness of terminations	No wire breakage and no damage of capacitor	Tense Strength of Terminal Load Force : 1.0 Kg Holding Time : 10 ± 1sec
Robustness of terminations	No wire breakage and no damage of capacitor	Bending Strength of Terminal Load Force : 0.5 Kg Bending Time : 4 x 90 ﾟ
Resistance to soldering heat	(1) Appearance : No visible damage (2) △C/C : ≤ ±5% of the initial value	Solder temperature: 260±5℃ Solder time: 5±0.5sec
Solderability	95% of the surface tinning	Solder temperature: 260±5℃ Solder time: 2±0.5sec
Rapid change of temperature	The capacitors shall be visually examined and there shall be no visible damage.	Lower category temperature: -40℃ Upper category temperature: 110℃ Number of cycles: 5 Duration t1 = 30 min
Vibration	The capacitors shall be visually examined and there shall be no visible damage	Frequency range: 10~55Hz Course: X,Y,Z (axis) 2h / axis ( 6h in total) Displacement amplitude: 0.75mm

Test items	Performance requirements	Conditions of test
Climatic sequence	(1) Appearance : No visible damage (2) △C/C : ≤ ±5% of the initial value (3) DF ( tanδ) : ≤ 0.008 of increased value (4) IR : ≥ 50% of the applicable limits (5) Voltage proof : Normal	Dry Heat Upper Temperature: 110℃ Lower Duration: 16Hrs
Climatic sequence		Cold Temperature: -40℃ Duration: 2Hrs
Damp Heat Steady State	(1) Appearance : No visible damage (2) △C/C : ≤ ±5% of the Initial value (3) DF ( tanδ) : ≤ 0.008 of increased value (4) IR : ≥ 50% of the applicable limits (5) Voltage proof : Normal	+40°C and 93% RH, 56 days
Charge and discharge	(1) Appearance : No visible damage (2) △C/C : ≤ ±10% of the initial value (3) DF ( tanδ) : ≤ 0.008 of increased value (4) IR : ≥ 50% of the applicable limits	Test voltage : √2 x URVAC 50 Hz Charge and discharge: 0.5sec/time Repeated for 10000 cycles
Endurance	(1) Appearance : No Visible Damage (2) △C/C : ≤ ±10% of the initial value (3) DF ( tanδ) : ≤ 0.008 of increased value (4) IR : ≥ 50% of the applicable limits	1.25 x UR VAC 50 Hz, once every hour increase to 1,000VAC for 0.1 second, 1,000 hours at upper rated temperature

Storage conditions

1 t should be noted that the solderability of the terminals may be deteriorted when stored barely in an atmosphere for a long preriods
2 It shouldn't be located in particularly high temperature and high humidity, it must submit to the following conditions(keeping in the original package)
Temperature: 35 MAX Relative humidity:60% MAX
3 Storage period:Losse:12 monthes max (from the manufacturing date marked on the label in package bag)

Enviroment requirement

1 Compliance with the requirement of RoHS.
2 Compliance with the requirement of REACH.
3 Without Halogen(as required).
4 Please see the attachment 2 for the test reprots of the Rohs and Reach by a third party

Quality Control

Product structure

Our Services

1.Inquiry and consulting support.

2.Sample testing support.

3.View our Factory.
4. After sending, we will track the products for you once every two days, until you get the product.If you have any questions about the problem, contact with us, we will offer the solve way for you.

Product Tags:


*From:	Your email address is incorrect!
*To:	Dongguan Chenglue Electronic co.,Ltd
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	X2 Safety Capacitor
Brand Name:	CG
Model Number:	X2-684K-275VAC-E41
Certification:	VDE，CQC
Place of Origin:	DongGuan China
MOQ:	10000 Pieces
Price:	Discuss
Payment Terms:	T/T
Supply Ability:	100000000 Pieces
Delivery Time:	15-21 work days
Packaging Details:	200pcs/ bag,carton size:45cm31cm34cm,inner box:29.2cm21cm31.3cm,a carton inside two inner boxs , 4000pcs/ box
Fetures:	Non-Induction Construction
Capacitance::	0.68uf
Rated Voltage::	250-310V
Material:	Metallized Polypropylene Film
Application:	General Purpose
Keyword:	X2 Safety Capacitor