JS-339 Tri Component EP Instant Dry Glue Adhesive Colorless Transparent

Product Description

JS-339 instant-drying adhesive is a medium-viscosity, surface-insensitive, general-purpose cyanoacrylate adhesive, suitable for rapid bonding of various plastics, woods, rubbers, metals, etc.

Product application
Suitable for various applications, especially for difficult-to-adhere and inert surfaces, as well as for bonding porous acidic and absorbent materials such as wood, paper, leather, etc., and it can be applied on the surface.

The material properties before solidification

Typical curing characteristics

Under normal circumstances, moisture on the surface of the material will trigger the curing reaction of this product. Although this product can reach the application strength completely within a relatively short period of time, it needs to cure for at least 24 hours to have complete chemical/solvent resistance. a. Relationship between curing speed and substrate
The curing speed depends on the substrate being bonded. The table below shows the curing time for different substrates at 22℃/50% relative humidity. The curing time is defined as the time when the shear strength of the sample reaches 0.1N/mm2.

b) Relationship between curing speed and bonding gap: The curing rate depends on the bonding gap. A smaller bonding gap leads to a faster curing speed, while an increased bonding gap will slow down the curing rate. The relationship between curing speed and accelerator
c) When the bonding gap is too large, causing the curing to be too slow, using an accelerator on the substrate surface can increase the curing speed. However, using an accelerator may reduce the final bonding strength. Therefore, it is recommended to conduct tests before using an accelerator.

Characteristics of the cured material
Test conditions: Temperature 23 ± 2℃, Relative humidity 50 ± 5%

Construction method

1. Due to the fast bonding speed, the workpiece must be accurately positioned before bonding, and the surface of the workpiece must be clean and free of grease.
2. This product is usually applied with manual gluing. A small amount of glue is applied to one side of the workpiece, and then the two sides are pressed together until the initial setting is achieved.
3. Generally speaking, the amount of glue applied should be minimized. Excessive glue application will lead to a decrease in the curing rate and bonding strength. The excess glue can be removed by using cleaning agents, nitroform, or appropriate organic solvent.
4. This product has the best bonding effect for small gaps (0.05 mm).

Notes for Attention

1. The instant adhesive will quickly bond to the skin. If it comes into contact with the skin, it can be rinsed with warm soapy water. Do not forcibly tear it off.
2. If it comes into contact with the eyes, immediately rinse with plenty of water and seek medical attention immediately; if it is accidentally ingested, seek medical attention immediately.
3. This product should not be used in pure oxygen or oxygen-rich environments, and it cannot be used as a sealing material for chlorine or other strong oxidizing substances.
4. Use the product in a well-ventilated area.

Product Storage
The ideal storage conditions for the product are to keep it in a cool and dry place with a temperature range of 8°C - 21°C. The optimal storage temperature is 2 - 8°C. Products used outside the packaging box may be contaminated during use. To avoid contaminating the unused adhesive solution, do not pour any adhesive solution back into the original packaging.

FAQ

1.What materials does jS-339 bond?
It bonds metal, plastic, ceramic, glass and wood for industrial multi-material applications
2. How fast does it cure?
lt delivers instant-dry initial bonding at room temperature and reaches full strength rapidly
3. Any mixing requirements?
Mix three components per specified ratio, stir well and apply right away.
4. How should l store it?
Keep sealed in cool, dry dark place; stay away from heat and open flame.

Wuxi Jungu Technology Co., Ltd. is a professional manufacturer and global supplier of silicone sealants, butyl rubber adhesives, EPDM bonding glue and construction sealing materials, located in Wuxi, Jiangsu Province, China.

We integrate independent R&D, modern production, strict quality inspection and global export sales. Our factory owns standardized automated production workshops, complete testing laboratories and stable large-scale production capacity to fulfill bulk wholesale and engineering orders worldwide.

Our core product series cover neutral weatherproof silicone sealant, structural silicone adhesive, insulating glass butyl sealant, EPDM profile adhesive, general-purpose sealing glue and special industrial bonding compounds, widely applied in window & door fabrication, curtain wall engineering, insulated glass processing, construction decoration and new energy industries.

All products comply with international standards and have passed SGS, RoHS, ISO9001 quality management system certifications. We provide customizable colors, formulas, packaging solutions, free product samples and full sets of export documents for global distributors, construction contractors and manufacturers.

We support flexible MOQ, fast stock delivery, sea freight, air freight and door-to-door express shipment. With professional overseas technical service teams, we offer one-stop sealing material solutions for clients from Southeast Asia, the Middle East, Europe, North America and Africa.

Adhering to stable quality, competitive factory direct prices and long-term win-win cooperation, Wuxi Jungu Technology has built long-term trusted partnerships with thousands of overseas customers. We sincerely welcome global buyers to visit our factory and establish stable cooperative relations.