| 1. SCOPE |
| Applicable Scope | 0.5mm Pitch FPC/FFC Connectors (Locking Series) | This specification covers the 0.5mm Pitch FPC/FFC Connectorsseries
Locking |
| 2. PRODUCT NAME AND PART NUMBER |
| Product Name | FFC/FPC Flat Cable Connector | |
| Part Number | AFC06-S**FIA-00 | FPC Connector 0.5mm Pitch Flip-Top Bottom Entry with Latch H2.0 |
| 3. RATINGS |
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | 0.5A | (AC/DC (Virtual value) 50Hz) |
| Ambient temperature Range | -45 +85 | |
| 4. PERFORMANCE |
| 4.1 Electrical Performance |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500 M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal
or ground. |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1
minute between adjacent terminal or ground. |
| 4.2 Mechanical Performance |
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC (0.3mm thickness) at the speed
rate of 253mm/minute. |
| Withdrawal Force | 0.49*n (N) MIN | Insert and extract applicable FFC (0.3mm thickness) at the speed
rate of 253mm/minute. |
| Terminal/Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 25 3mm per minute. |
| 4.3 Environmental Performance and Others |
| Repeated Insertion and Withdrawal | Contact Resistance 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate
of less than 10 cycles/minute (no power). |
| Temperature Rise | 30 MAX | Carrying rated current load (UL 498). |
| Vibration | Discontinuity 1 ms MAX. Appearance: No Damage. | DC 1mA energized; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz/min;
Duration: 2 hours in each X, Y, Z axes. |
| Shock | Discontinuity 1 ms MAX. Appearance: No Damage. | DC 1mA energized; 490m/s {50G}, 3 strokes in each X, Y, Z axes. |
| Heat Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | Mate applicable FPC/FFC; placed in 852 for 96 hours, then return to
room temperature for 1-2 hours. |
| Cold Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | Mate applicable FPC/FFC; placed in -402 for 96 hours, then return
to room temperature for 1-2 hours. |
| Humidity | Insulation Resistance 20 M MIN. Appearance: No Damage. | Mate applicable FPC/FFC; placed in 402, 90-95% RH for 96 hours,
then measured within 0.5 hours at room temperature. |
| Temperature Cycling | Contact Resistance 60 m MAX. Appearance: No Damage, no corrosion. | 5 cycles of: 30 min at -452, 10-15 min at room temp/humidity, 30
min at 852, 10-15 min at room temp/humidity. |
| Salt Spray | Contact Resistance 60 m MAX. Appearance: No Damage. | 484 hours exposure to a salt spray from a 51% solution at 352.
Post-test wash with room temperature water and dry. |
| SO2 Gas Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | 24 hours exposure to 505ppm SO2 gas at 402. |
| NH3 Gas Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia
solution. |
| Solderability | Solder Wetting 95% | Soldering Time: 20.5 sec. Soldering Temperature: 2355, 0.2 mm from
terminal tip. |
| Resistance to Soldering Heat | Appearance: No Damage, no deformation. | Soldering Time: 50.5 sec. Soldering Temperature: 2605, 0.2 mm from
terminal tip. |
