Product Details
Company Profile

Microwave ON/OFF Motion Sensor, Rotary Switch Setting, With Low Stand-by Power

【Product Feature】

Conform to new ERP standards; low stand-by power.
5.8GHz microwave license-free ISM wave band; bulk order are compliant with RED&TUV approval.
Compact size design, can be built-in most of light fixtures.
Simple to operate: adjusting rotary switches to change detection area, hold time, daylight sensor and other parameters.
Input and output terminals are convenient for connecting.
Five year warranty

【Parameter】

Input
Voltage Range	110-240VAC 50/60Hz
Stand-by Power	≤0.1W
Surge Test	L--N: 4kV
Output
Output Control	ON-OFF
Load Capacity	200W@230Vac(Inductive/LED) ; 400W@230Vac(Resistive) 400W@230Vac(Inductive/LED)800W @230Vac(Resistive)
Max. Surge Capacity	30A (50% Ipeak, twidth =500us, 230Vac full load, cold start); 60A (50% Ipeak, twidth =200us, 230Vac, full load, cold start)
Sensor Parameter
Operating Frequency	5.8 GHz ±75MHz, ISM wave band.
Transmitting power	1mW Max.
Hold time	5s/30s/1min/5min by rotary switch
Detection Area	100%/75%/50%/25% by rotary switch
Daylight Sensor	10Lux/30Lux//50Lux/Disable (Diffusion) by rotary switch
Detecting Radius	Ceiling installation 3m height: 1m/s ≥ 2.5m, 0.3m/s ≥ 3.5m Test condition: Product setting 100% sensitivity, 60㎡indoor open space
Mounting Height	3m (ceiling mounting),6m Max)
Environment
Operating Temperature	-25~60°C
Storage Temperature	-40℃~80℃, Humidity: ≤85%(Non-condensing)
Maximum Shell Temperature (Tc)	80℃
Certificate Standard
Certificate	CE, RED
Environmental Requirement	Compliant to RoHS 2.0, Reach
IP Rating	IP20
Product Category	Class II
Other
Wiring	Press-in type terminal block, wiring 0.75-1.5 mm²
Installation	Built-in
Package	Bubble bag + Clapboard + Carton(K=A)
Net Weight	37.8±3g
Lifetime	5 years warranty @Ta

【Function】

√ON-OFF function	Setting daylight sensor to “disable” or ambient brightness is lower than the preset daylight sensor value, when detecting moving signals sensor starts working and light will turn on. When hold time ends, light will turn off.
○2-step dimming	N/A
○3-step dimming	N/A
○Daylight harvesting	N/A
○Daylight priority	N/A
○High-low sensitivity	N/A
○Grouping	N/A

【Product Information】

Dimension(units: mm)

Structure

Wiring

Note:*The sensor is designed for connect one load only. Connect more than one loads may damage the sensor.

Installation instruction

Note:

When installation, please pay attention to the front of microwave antenna is not allowed to be blocked by metal.

The AC incoming line needs to keep a distance of more than 10mm from the BUCK inductance, Otherwise it will cause conduction to fail. As shown in the following figure.

【Detection Range】

【DIP Switch Setting】

Sensor should be installed by a professional electrician. Please turn off power before installing, wiring, or setting the DIP switches.

Microwaves cannot penetrate metal. Do not place product in a closed or a half-closed metal lamp. Neither metal nor glass is not allowed to cover above the product. If antenna needs to pass through the metal plate, please ensure that the top of sensor is close to the metal plate.

The installation spacing between sensors is recommended to be greater than 2m. Keep it away from wireless devices such as switches and routers, and the installation spacing between sensors and routers is recommended to be greater than 2m. The antenna surface of the microwave sensor should be away from the input AC and output DC to avoid low/high frequency signals affecting the normal operation of the microwave sensor antenna.

Sensitivity area is related to moving speed of objects, size of moving objects, mounting height, mounting angle, working environment, reflecting materials and etc.. Given detecting area is typical value that was measured by 165cm high testers in an indoor open environment.

This model is suitable for ceiling installation. If wall installation is used, the microwave sensor sensing detection area is greatly increased, and it may cause the phenomenon of microwave penetrate wall or the light not going out. So please adjust the sensitivity to 10%. If the sensitivity 10% can not be used, please avoid to the wall installation or ask the manufacturer for technical support.

The daylight thresholds are measured on a sunny day without shadow and in an ambient light diffuse reflection status. Different environment and climate cause different brightness values that daylight sensor measures.

Sensor should not be covered or hided by metal, PCB, LED tray etc..The spacing between the sensor antenna and surrounding materials should be greater than 5mm. There should be no metal or PCB tracks near the sensor antenna, above or below it. The recommended thickness of cover is 2mm, and keep the spacing between the sensor antenna and cover is greater than 3.2mm.

Vibration signals will be regarded as moving signals to trigger sensor. Installing sensor should be away from the object that vibrates for a long time, such as large metal equipment, pipes, air conditioning outlets, exhaust vents, smoke exhaust machine ports, shaking fans, etc. Pets in detecting area may cause false trigger.

The antenna surface of microwave module should be away from input AC, output DC, rectifier bridge, transformer, switch tube and other high-power devices to avoid high frequency signals affecting the normal operation of microwave sensor’s antenna.

Sensor is for indoor use only. The waterproof effect for outdoor or half-outdoor use will be affected. Wind, rain, and moving objects may cause false triggering. When the sensor is installed in a metal lamp, a metal reflective surface or a small enclosed environment, the microwave will be reflected many times and cause false triggering, please reduce the sensitivity or ask the manufacturer for technical support.

When ambient temperature is over 80'C, over temperature protection may be triggered (automatic recovery after cooling

For the new installation environment, it is recommended to test 5pcs samples before installation.

Product Tags:


*From:	Your email address is incorrect!
*To:	Shenzhen Merrytek Technology Co., Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	Microwave Motion Sensor
Brand Name:	Merrytek
Model Number:	MC030S 7
Certification:	CE, RED
Place of Origin:	Shenzhen, China
MOQ:	100pcs
Price:	Negotiable
Payment Terms:	T/T
Supply Ability:	10000 pcs/month
Delivery Time:	1, Sample and small order: Within 5 working days after receiving your payment. 2, Bulk order: 4-5 weeks after receiving deposit.
Packaging Details:	Bubble bag + Clapboard + Carton(K=A)
Voltage Range:	110-240VAC 50/60Hz
Output Control:	ON-OFF
Operating Frequency:	5.8 GHz ±75MHz, ISM wave band.
Mounting Height:	3m (ceiling mounting),6m Max）
Operating Temperature:	-25~60°C
Lifetime:	5 years warranty @Ta