IEC60320-1 Appliance Couplers Testing Equipment Power Cord Bending Test Apparatus with 16A Output Current
|
...Appliance Couplers Testing Equipment Power Cord Bending Test Apparatus with 16A Output Current 1. Introduction Power cord bending test apparatus designs to meet the test requirements of IEC60320-1 clause 22.3, for applying bending test to cord of connectors and plug connectors. The test apparatus is configure with 7 inch LCD touch screen, PLC and step motor. The flexing angle, flexing speed an test......
Pego Electronics (Yi Chun) Company Limited
|
Coupler Pulling Test Apparatus Connector To Pull Test For Household IEC 60320-1
|
... general purposes- Part1:General requirements" clause 23.3 and figure 19. Test principle For Coupler Pulling Test Apparatus: The connector is inserted into an appliance inlet of a type corresponding with the connector to be tested and complying with the...
Sinuo Testing Equipment Co. , Limited
|
IEC 60884-1 Bending Test Apparatus bend tester without screw thread
|
...Bending Test Apparatus bend tester without screw thread Production introduction: According to the provisions of IEC 60884-1, GB2099.0-1996,12.3.12 provisions of the non threaded terminal bending testing machine. The test machine without screw thread is mainly used for the bending test and the pressure drop of the wire after the wire is connected to the non threaded terminal. Main technical parameters: Power supply AC220V 5A 50Hz Test...
Guangzhou HongCe Equipment Co., Ltd.
|
IEC 60702-1 Clause 13.6 Electric Vehicle Cables Bending Test Apparatus
|
... to the standard requirement of IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to ......
Sinuo Testing Equipment Co. , Limited
|
Manual Control 60811 IEC Test Equipment Cold Bend Testing Apparatus
|
... Methods for general application-Test at low temperature clause 8.1 and 8.2 and figure 1. Figure 1 Cold Bend Test Apparatus Application: This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a...
HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
|
IEC 60598-2-21 Figure 2 Cold Bend Test Apparatus To Measure Dynamic Bending Performance Of Wire And Cable
|
...Test Machine Overview Product description This Cold bend test apparatus is used to measure the dynamic bending performance of wire and cable under low temperature conditions, and is suitable for outer diameter less than or equal to 12.5mm round wire and cable or round insulated wire core is the wire and cable industry to test the bending......
KingPo Technology Development Limited
|
IEC60851-3 Bending Test Apparatus For Flat Wires With Test Bars
|
...bending test apparatus is applicable to the bending test of various enameled flat wires, paper wrapped flat wires, glass fiber wrapped flat wires, film wrapped wires and other electromagnetic wires with a wide edge of less than or equal to 16mm, as well as the corresponding copper and aluminum flat wires. Major Technical Parameters Bending......
Advanced Instruments Co.,Limited
|
Figure 2.8 Plug Socket Tester Pin Bending Test Apparatus
|
...Bending Test AS / NZS 3112 Figure 2.1 dimensions of plugs Figure 2.2 apparatus for flexing test Figure 2.3 form of pin Figure 2.4 dimensions of insulation on insulated live pins Figure 2.5 pressure test apparatus for insulation on insulated plug pins at high temperature Figure 2.6 impact test apparatus for insulation on insulated plug pins at low temperature Figure 2.7 abrasion test apparatus......
Guangzhou Shice Equipment Co., Ltd.
|
Hydraulic Construction Material Testing Equipment Bending Test Apparatus
|
Electro-Hydraulic Servo Microcomputer Control Universal Test Machine Compression Bending Product Profile The testing machine is mainly suitable for steel strand stretching and metal material stretching, compression, bending, shearing and other tests. ......
Chengdu Recen Technology Co., Ltd.
|
AC220V 50HZ Power Cord Flexing Test Apparatus With Digital Display
|
...Adjustable Bend Angle Product information: This test apparatus checks the protection of the supply cord where it enters the appliance. It conforms to the standard requirement of IEC60335-1 clause 25.14. Appliances provided with a supply cord that are moved...
Dongguan Kingpo Technology Limited
|
Submit your “appliance couplers bending test apparatus” inquiry in a minute :