manual IEC Test Equipment IEC 60811 Cold Bend Test Apparatus For Cables Sheaths And Insulation
|
... bending performance of wire and cable at low temperature. The equipment is mainly composed of low temperature thermostat, winding device and material testing system. It is suitable for circular wire and cable with outer diameter less than or equal to...
Guangzhou HongCe Equipment Co., Ltd.
|
Manual Control 60811 IEC Test Equipment Cold Bend Testing Apparatus
|
... Methods for general application-Test at low temperature clause 8.1 and 8.2 and figure 1. Figure 1 Cold Bend Test Apparatus Application: This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a...
HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
|
IEC 60811-1 Elongation Test Apparatus For The Insulating Sheath Of Electric Wire
|
... of IEC 60811-505, IEC 60811-1-4, VDE 0472 Part 616, and etc. It is applicable for the insulating sheath of the high polymer material, electric wire, rubber, and plastic to do the elongation test at the environment of -35°~0°. Technical Parameters For...
Sinuo Testing Equipment Co. , Limited
|
IEC 60598-2-21 Figure 2 Cold Bend Test Apparatus To Measure Dynamic Bending Performance Of Wire And Cable
|
IEC 60598-2-21 Figure 2 Low-temperature Winding Test Machine Overview Product description This Cold bend test apparatus is used to measure the dynamic bending performance of wire and cable under low temperature conditions, and is suitable for outer diameter less than or equal to 12.5mm round wire and cable or round insulated wire core is the wire and cable industry to test the bending......
KingPo Technology Development Limited
|
Cold Bend Test Apparatus SUS304 Electrical Safety Test Equipment
|
Cold Bend Test Apparatus IEC60811-1-4 for Cable Made by SUS304 Stainless Steel 1. Introduction The cold bend test apparatus is designed according to IEC60811-1-4 clause 8.1 and figure 1, IEC60884-1, VDE0472, GB2951.4 and GB2099-94. It is applied to the test......
Pego Electronics (Yi Chun) Company Limited
|
IEC 60811-403 Environmental Test Chamber Ozone Resistance Testing
|
...estimate the resistance of elastomeric material and polymeric materials of electric cables to ozone attack . The test apparatus shall consist of Test Chamber, Ozone Generator with High Voltage source & controller, Air Driers/Purifier, Flowmeter Control,...
DONGGUAN DAXIAN INSTRUMENT EQUIPMENT CO.,LTD
|
IEC 60702-1 Clause 13.6 Electric Vehicle Cables Bending Test Apparatus
|
... to the standard requirement of IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to ......
Sinuo Testing Equipment Co. , Limited
|
Luminaries Testing IEC60598-2-21 Cold Bending Test Device
|
...test whether the wire or rope lamp has cracks when it is wound at low temperature. The lamp is wound on the appliance shown in Figure 2, with a winding diameter of 4-5 times its own ......
SKYLINE INSTRUMENTS CO.,LTD
|
AC220V 50HZ Power Cord Flexing Test Apparatus With Digital Display
|
...Adjustable Bend Angle Product information: This test apparatus checks the protection of the supply cord where it enters the appliance. It conforms to the standard requirement of IEC60335-1 clause 25.14. Appliances provided with a ......
Dongguan Kingpo Technology Limited
|
AS/NZS3112 Figure 2.8 Pin Bending Test Equipment
|
AS/NZS3112-Figure 2.8 Application of force for pin bending test AS/NZS3112-Figure 2.1 (in part) dimensions of plugs AS/NZS3112-Figure 2.2 Apparatus for flexing test AS/NZS3112-Figure 2.3 Form of pin AS/NZS3112-Figure 2.4 Dimensions of insulaton on ......
Guangzhou Shice Equipment Co., Ltd.
|