IEC62196-1 Clause 26.4 EV Plug And Vehicle Connector Cable Bending Test Apparatus For Flexing Test
|
... to IEC62196-1 clause 26.4 figure 20 and table 14, it is applied to do mechanical load flexing test of the non-rewirable accessories of ev plug and vehicle connector. Test method: The sample is fixed to the oscillating member of the apparatus so that at...
Pego Electronics (Yi Chun) Company Limited
|
IEC 60702-1 Clause 13.6 Electric Vehicle Cables Bending Test Apparatus
|
... to the standard requirement of IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to drive the...
Sinuo Testing Equipment Co. , Limited
|
Switched Socket Outlets Vehicle Connectors Withdrawal Force Test Apparatus
|
... 14.1.6, fig13, fig14, table 5.It is used to check the maximum force required when the plug is pulled out of the socket-outlet or connector. Technical parameters: 1. The frame is composed of a bottom plate, a column, a sample installation fixture, and a...
Sinuo Testing Equipment Co. , Limited
|
IEC 60598-2-21 Figure 2 Cold Bend Test Apparatus To Measure Dynamic Bending Performance Of Wire And Cable
|
...Test Machine Overview Product description This Cold bend test apparatus is used to measure the dynamic bending performance of wire and cable under low temperature conditions, and is suitable for outer diameter less than or equal to 12.5mm round wire and cable or round insulated wire core is the wire and cable industry to test the bending......
KingPo Technology Development Limited
|
IEC 60227-2 Cable Testing Equipment Bending Test Apparatus For Tinsel Cord 0-1A Output Current
|
...h 60 000 bending cycles, i.e. 120 000 single strokes, interruption of the current shall not occur. Cable Testing Equipment After the test, the sample shall withstand the voltage test carried out in accordance with 2.2 of IEC 60227-2, the voltage, however,...
Guangzhou HongCe Equipment Co., Ltd.
|
Manual Control 60811 IEC Test Equipment Cold Bend Testing Apparatus
|
... Methods for general application-Test at low temperature clause 8.1 and 8.2 and figure 1. Figure 1 Cold Bend Test Apparatus Application: This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a...
HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
|
800W Cable Bending Test / Flexing Test Apparatus Six Station 800 Watt
|
Wire/Cable Bending Tester (MY-XC-C6), Sheet metal material with white color Description This testing machine is customized according to the "General Safety Requirements for Communication Cord and Power Cord" and is written by advanced touch screen. PLC ......
Shenzhen Mingyu Instrument And Equipment Co., Ltd.
|
IEC60851-3 Bending Test Apparatus For Flat Wires With Test Bars
|
Performance Characteristics 1.Executive standard: GB/T4074.3-2008,IEC60851-3; 2.This bending test apparatus is applicable to the bending test of various enameled flat wires, paper wrapped flat wires, glass fiber wrapped flat wires, film wrapped wires and ......
Advanced Instruments Co.,Limited
|
UL87 200W Bending Angle Adjustable Cable Bending Tester
|
Bending angle 10-360° Adjustable Wire Bending Test Machine Wire Life Testing Apparatus Application Test plug lead wire and the bending strength of the wire, can be automatically counted at the same time show the conductor resistance of the wire, the test ......
Guangdong Aisry Instrument Technology Co., Ltd.
|
Cord Bend Test Equipment / Tensile testing machine 10 - 40 mumbers/min Speed
|
... cable forward to the center of the turnplate. Pull the cable vertically with load at rated bending speed, angle and times then to begin the bending test. When the tester stops automatically, check the jacket damage and the breakage rate of conductors....
Infinity Machine International Inc.
|